Illustration of a house with solar panels on its roof under a bright sun

Why quotes are hard to compare

Two solar proposals for the same house can look completely different. One leads with a monthly payment, another with twenty-five-year savings, a third with a glossy production chart. The trick is to strip each quote back to the same handful of facts and put them in a simple table. This guide walks through the lines worth extracting and what to ask when something is missing.

Line 1: System size (kW DC)

Start with the size of the array, usually stated in kilowatts of direct-current capacity. It equals the number of panels multiplied by each panel's rated wattage. If one quote proposes a much larger or smaller system than the others, ask why. The answer may be sensible (a different roof layout, different usage assumptions) or it may reveal that someone sized for your bill without looking at your roof.

Line 2: Estimated annual production (kWh)

Production is what actually offsets your bill. Ask how it was estimated: which modelling tool, what shading assumptions, and whether it is a first-year figure. Divide production by system size to get a "kWh per kW" ratio. Quotes for the same roof should land in a similar range; an unusually high ratio deserves a question.

Line 3: Total price and price per watt

Write down the gross price before any incentives, and divide it by the system size in watts. Price per watt lets you compare differently sized systems on a like-for-like basis. Be careful with quotes that show only a net price after incentives; as of 2026 the federal residential credit is no longer available for new homeowner purchases, so any credit shown should be one you can verify applies to you.

Line 4: Equipment

List the panel model, inverter type (string inverter, microinverters or optimisers) and any battery. You do not need to be an expert to compare them. Look up the datasheets, note the product warranties, and check that each installer is quoting specific models rather than "tier one panels" or "equivalent".

Line 5: Warranties

There are usually three: the panel product warranty, the panel performance warranty (how much output is guaranteed over time), and the installer's workmanship warranty covering leaks and installation faults. Add the inverter warranty as a fourth. Note the length of each and who you would actually call if something went wrong.

Line 6: Scope of work

Check what is included: permits, utility interconnection paperwork, electrical panel upgrades, roof penetrations and flashing, monitoring setup, and removal of debris. An apparently cheaper quote can become more expensive once an excluded panel upgrade is added.

Line 7: Financial assumptions

Savings projections depend on assumptions about future electricity prices, export credits and degradation. Write down the annual utility price increase each installer assumed. A quote assuming steep annual increases will always look better; re-run it with a more modest figure in a calculator to compare fairly.

Line 8: Financing terms

If a loan is offered, record the interest rate, term, any dealer fee built into the price, and whether there is a balloon payment expectation tied to an incentive. For leases and power purchase agreements, record the escalator, the contract length and what happens if you sell the house.

A simple comparison table

  • Installer name and quote date
  • System size (kW) and number of panels
  • First-year production (kWh) and kWh per kW
  • Gross price and price per watt
  • Panel, inverter and battery models
  • Product, performance, inverter and workmanship warranty lengths
  • Exclusions and possible extra costs
  • Assumed utility price increase and export credit

Incentive note (October 2026): the US federal residential clean energy credit (Section 25D) ended for expenditures made after 2025, so a homeowner buying a system today should not assume a 30% federal credit. State, local and utility programs vary and change often; check what is currently available where you live before relying on any incentive in an estimate.

Making the decision

Once the table is filled in, the cheapest price per watt is only one factor. Clear answers, realistic production estimates, a solid workmanship warranty and an installer who explains rather than pressures often matter more over the life of a system. If a figure in a quote cannot be explained, treat that as useful information in itself. FreshSuns does not recommend specific installers; the goal is simply to help you ask better questions of the ones you contact.

About Freshsuns

Free solar planning calculators and plain-language guides for homeowners. Learn more.

Newsletter